How do you remove a stuck crankshaft pulley bolt?

4 Ways To Remove A Stuck Crankshaft Pulley Bolt

1. Soak in Lubricant. Although the bolt sits on the side of the engine, you can use putty to create a sticky dish for your lubricant of choice.
2. Rent A Powerful Impact.
3. Try a Long Breaker Bar.
4. Bump the Starter.
5. Take It To A Shop.

How do you remove a crankshaft bolt without impact?

Starts here2:11How to remove a tight crankshaft pulley bolt without an impact wrenchYouTubeStart of suggested clipEnd of suggested clip61 second suggested clipYou know somewhere work and working like if the handle of the wrench is right here say on the axleMoreYou know somewhere work and working like if the handle of the wrench is right here say on the axle it’s pretty firm. I’ll actually put it on there. Set it up in place and then bump the starter.

How do you remove a stuck harmonic balancer bolt?

Starts here2:32How to remove a stuck harmonic balancer bolt – YouTubeYouTubeStart of suggested clipEnd of suggested clip61 second suggested clipAnd tighten them down. You. Can see that that that steel is resting against the bracket to the motorMoreAnd tighten them down. You. Can see that that that steel is resting against the bracket to the motor mount right there on that that cast-iron bracket. So it’s got a solid surface to rest against.

How do you get a nut off a pulley?

Starts here5:40stripped pulley bolt/nut extraction methods – YouTubeYouTubeStart of suggested clipEnd of suggested clip59 second suggested clipAnd then you can take your screwdriver. Or your chisel put it inside of that notch.MoreAnd then you can take your screwdriver. Or your chisel put it inside of that notch.

How do you remove a 2jz crank bolt?

Starts here2:022JZ Crank Bolt Hack – Starter Bump Method – Works For Most RWD Cars!YouTube

How do you break a crankshaft bolt?

Starts here4:20How to Remove Crank pulley bolt EASY! breaking threadlockerYouTube

How do I remove a harmonic balancer bolt without a puller?

How to remove a harmonic balancer without a puller?

1. Access the harmonic balancer by removing the serpentine belt.
2. Find the center bolt and remove it using a socket.
3. Remove the pulley.
4. Remove the harmonic balancer using a durable strap.

How do you remove a camshaft pulley bolt?

Starts here4:03How to Loosen Bolt on Camshaft Pulley Before Removing Timing BeltYouTube

How do I remove the idler pulley bolt?

Starts here3:40How to Remove Idler Pulley – YouTubeYouTube

How do I remove a 1jz harmonic balancer?

Starts here11:511JZ VVTI How to Remove Crank pulley 1jz/2jz #Nissan240sx #1jzgteYouTube

How do you use a harmonic balancer?

Starts here3:28Harmonic Ballancer Bolt Puller set how to use it. – YouTubeYouTube

Can you pull a harmonic balancer without a puller?

The center bolt is the bolt that holds the harmonic balancer with the crankshaft. You cannot remove the harmonic balancer without removing the center bolt first. So, using a socket that fits the bolt, remove it and safely place it nearby.

How do you remove the crankshaft pulley?

Thread the bolts in by hand, and adjust the depth of the bolts so that the puller is square with the face of the pulley. Tighten the central puller bolt until you remove all the slack. Using a breaker bar and socket, tighten the central puller bolt until the pulley slides off the crankshaft.

How to torque crankshaft pulley?

– (1) Clean the crankshaft pulley thread using an air gun. – (2) Apply engine oil to the crankshaft pulley bolt seat and thread. – (3) Tighten the bolts temporarily with tightening torque of 44 N·m (4.5 kgf-m, 33 ft-lb). – (4) Tighten the crankshaft pulley bolts.

What is the crankshaft pulley?

Located at the front end of the crankshaft, the crankshaft pulley is what drives the alternator and other engine components. The crankshaft pulley is also called a harmonic balancer, and is a visible wheel mounted to the crankshaft. The crankshaft pulley is responsible for turning the belts that operate the engine and other accessories.